Skip to content
RESEARCH-BASED GUIDES. PRACTICAL EVERYDAY ADVICE.How we pick products
AFAir Fryer Kitchen SupplyYour everyday air fryer companion
How to Choose

How to Measure a Window for Inside-Mount Blinds

Inside-mounted blinds need measurements that follow the maker's ordering rules. Small differences in the recess can affect fit.

We may earn a commission from qualifying purchases. How we pick products

Where to buy

Check the latest price, availability and delivery on Amazon. Orders are placed on Amazon. We may earn a commission from qualifying purchases.

Read the full guide ↓

Inside-mount blinds sit within the window recess, so the fit is tight and small errors show. The recess is rarely perfectly square, and each maker has its own ordering rules for how the blind is made to suit the measurements you give. Following those rules closely matters more than any rule of thumb.

What to do

Measure the recess at several points across the width and height, using a steel tape that does not sag. Record the depth and note any obstructions such as handles, locks or a sloping sill. Then use the seller’s stated deduction and ordering process for the order dimensions.

In this guide

Take the measurements

  • Width: measure at the top, middle and bottom of the recess. Recesses can narrow in places, and the smallest figure is usually the one that decides.
  • Height: measure at the left, centre and right, from the top of the recess to the sill.
  • Depth: measure how far the recess goes in, since the blind headrail and fixings need a minimum depth.
  • Obstructions: note handles, hinges, cranks and trims that sit inside the space.

Write each figure down immediately, with the unit, so you do not rely on memory.

A mistake to avoid

Do not subtract an allowance yourself if the seller already makes that deduction. Double-adjusting can produce a blind that is too small and leaves visible gaps. Read the ordering instructions carefully to see whether they want the exact recess size or a figure with an allowance taken off.

A detail worth checking

Check the recess depth against the complete operating assembly. A blind can have the correct width yet still conflict with a window handle or prevent the window from opening as intended. If the depth is shallow, check whether the blind has a shallow-recess option or whether an outside mount would work better.

Try this practical check

Keep a raw measurement sheet separate from the order dimensions. Label each window clearly with the room and position, so a wider figure from another room cannot be confused with this one. When you have finished, go back and re-measure one or two at random to confirm you read the tape the same way each time.

A Worked Example With Three Sets of Numbers

Seeing the process on a real window makes the logic clear. Imagine a recess that, when measured with a steel tape, gives three width readings: one near the top, one in the middle and one near the bottom. The readings differ slightly because the walls are not perfectly parallel. For height, you take a left, centre and right reading, and those differ too.

The usual approach is to record all six numbers, then use the narrowest width and the tallest or shortest height depending on the maker’s ordering rules. Many suppliers want the narrowest width so the blind never jams, and they handle the small allowance at the sides themselves. Others ask for the exact figures and apply their own deductions. This is why reading the supplier’s measuring guide before you pick up the tape is so important.

Write the numbers on a small card, label each one clearly as top, middle or bottom, and note the units. Then take a photo of the tape against the window as a record. If an order goes wrong later, those notes show exactly what you measured and when.

Choosing and Using the Right Measuring Tools

A flexible sewing tape bends and sags, so it is a poor choice for a window recess. A rigid steel tape with a clear lock gives more reliable readings, especially across wide openings where the tape needs to stay straight.

What to have on hand

  • A steel tape measure with a locking button.
  • A pencil and a card for noting results.
  • A small spirit level to check whether the sill and head are level.
  • A step stool, so you can read the tape at eye level for the top of the window.

Reading the tape accurately

Hook the end firmly against one side, pull the tape tight across to the other side and read the figure at the opposite edge. Look straight at the marks rather than from an angle, since a sideways glance shifts the apparent reading. Repeat each measurement twice. If two readings of the same spot disagree, measure a third time and work out why.

Understanding Why Recesses Are Never Perfect

Few window openings are truly square. Plaster builds up unevenly, frames settle, and decorators add layers of paint and filler over the years. These small differences matter because a blind that fits snugly needs to be made to the right size, not a close approximation.

When you check for square, measure the two diagonals of the recess from corner to opposite corner. If they match, the opening is square. If they differ noticeably, the window is out of true, and you should note this when ordering or speaking to the supplier. Some makers can adjust for slight differences, while others recommend a different type of fitting for badly distorted openings.

Also check whether anything protrudes into the recess, such as a window handle, a hinge, a lock or a trim that narrows the opening. These are easy to miss and cause real fitting problems when the blind arrives. Hold the tape across the narrowest point you can find, not just at the easy spot.

Depth, Clearance and Where the Blind Will Sit

Inside-mount blinds need a certain amount of flat space for the headrail to sit in. The recess depth is therefore as important as the width and height. Measure from the face of the wall back to the first obstruction, such as the glass, a handle or a frame lip.

Different styles need different depths, and the supplier or product listing will specify what each one requires. Check the exact figures given for your chosen blind rather than relying on memory or a rule of thumb. If the recess is too shallow, you may need a different style, a surface-mount option or a special fitting.

Check What to look for If there is a problem
Recess depth Enough flat space for the headrail Choose a style with a shallower fitting
Window handle Does it hit the blind when opened Allow extra clearance or pick another style
Frame lip Does it narrow the opening Measure at the narrowest point
Sill slope Does the bottom edge sit flat Mention it to the supplier

Reading the Supplier’s Instructions Closely

Every maker has its own measuring guide, and the details differ. Some want measurements to the nearest millimetre, some accept a different rounding, and some ask you to say whether you measured width or height first. A few apply a standard deduction on their side, which means you should send the raw recess figure and not subtract anything yourself.

Before ordering, go through the guide line by line and check these points:

  • Which measurement they want: the narrowest width, the exact width or something else.
  • Whether they deduct an allowance for you.
  • How they want height recorded and whether the sill or frame matters.
  • What happens if the blind arrives wrong, and whether made-to-measure orders can be changed.

Keep a copy of the page you followed. If a dispute arises, that is your reference.

Troubleshooting Awkward Windows

Some windows need extra thought. Here are common situations and sensible ways to approach them.

Tilt-and-turn and inward-opening windows

When the sash swings into the room, the blind must clear it. Check how far the window opens, and whether the blind sits inside the recess in front of or behind the frame lip. You may need a style that fixes close to the glass.

Bay and corner windows

Treat each pane as its own window and measure separately. Label each one, such as left, centre or right, so the correct blind goes in the correct place.

Skylights and angled windows

These often need blinds designed for the specific frame. Look up the maker’s model details and ask the supplier before measuring.

Recesses with trim or beading

Measure at the narrowest and shallowest point. If trim limits the fit, mention it when ordering.

Child Safety and Final Checks Before You Order

Blind cords and chains can be a hazard around young children. Follow the maker’s safety instructions and any official guidance in your area, and use the safety devices supplied with the blind. If you are unsure, ask a qualified professional or the supplier for advice.

Before confirming your order, run through a short checklist:

  1. Three width readings and three height readings are written down.
  2. You have checked depth and clearance for handles and frames.
  3. You have confirmed which figures the supplier wants.
  4. You have noted the units and double-checked the tape reading.
  5. You have photographed the window and the tape.
  6. You have read the return policy for made-to-measure items.

Short glossary

  • Recess: the opening in the wall around the window.
  • Headrail: the top part of the blind that holds the mechanism.
  • Sill: the horizontal surface at the bottom of the window.
  • Reveal: the side surface of the recess between the wall face and the glass.

Special Cases: Very Wide and Very Narrow Openings

Extremes need extra attention. A very wide opening may exceed the maximum width a single blind can be made, so the supplier may recommend two blinds side by side or a different product. A very narrow opening may fall below the minimum size for certain mechanisms. Check the size limits in the product listing before you fall in love with a style.

With wide openings, take extra width readings along the span, since walls can bow slightly in the middle. Hold the tape taut and have a helper support the far end if the span is long. For narrow openings, measure with extra care, because a small error is a larger share of the total.

When two blinds share one recess, ask the supplier how much gap they leave between them and where the dividing point should be. Mark the centre line lightly in pencil so both blinds line up with the window.

Fitting day preparation

Before the blind arrives, clear the sill, wipe the recess and make sure you have the screwdriver and any fixings the instructions mention. Check the wall type, because the right fixing for plasterboard differs from masonry or timber. If you are unsure, ask a qualified fitter.

Quick Answers

Should I measure in millimetres or centimetres?

Use whichever unit the seller’s form asks for and stay consistent. Millimetres reduce rounding errors.

What if the three width measurements differ?

Follow the seller’s instructions, which commonly use the narrowest figure. If the difference is large, ask them how to proceed.

Can I fit inside-mount blinds on a window with a shallow recess?

It depends on the blind’s fixing depth. Check the minimum depth in the product details before ordering.

Tools and Preparation Before You Start

Accurate blind measurements begin with a few simple tools and a clear window. A steel tape measure is best, because it stays rigid across the width of the window and does not stretch. A pencil, paper and a stepladder for tall windows complete the kit. If you have a laser measure, you may use it, but check that it reads from the correct edge and agrees with the tape.

Clear the window area first. Open curtains, remove old blinds and any hardware inside the recess, and check that the glass, trim and sill are free of loose items. Clean surfaces so that the tape sits flat against them. Take note of the type of window: tilt-and-turn, casement, sash, bay or tall patio-style. Each has parts that may interfere with a blind, such as cranks, handles and hinges.

Label a sheet for each window with the room and position, such as kitchen left or bedroom front. Measure in the same unit throughout, and write the number immediately. Work from the same side each time, and keep the tape level and square to the frame. If the window is difficult to reach, ask someone to hold the tape end so it does not slip. Check the manufacturer’s measuring guide before you begin, because ordering rules differ between sellers.

Checking the Recess for Square and Level

Few window recesses are perfectly square. Walls may lean, plaster may bulge and old frames may have settled, so a recess can be narrower at the bottom than the top or taller on one side. That is why measurements are taken at several points, and why the smallest reading often drives the order.

Compare the three width readings and the three height readings. If they differ by only a small amount, the blind should fit within the seller’s tolerances. If the difference is larger, ask the seller how to proceed, since some makers offer to adjust or allow for it, and others may suggest a different mounting type.

Check the diagonals as an extra test: measure from one top corner to the opposite bottom corner, then the other pair. Equal diagonals suggest a square opening. Unequal ones indicate that the recess is out of square. Also check that the top surface of the recess is flat enough to take a headrail bracket, and that there is solid material, not crumbling plaster, for fixings. Look for bumps, caulk lines or trim that stand proud of the surface and could prevent the blind from sitting flush. Record any feature that might affect the fit.

Blind Types and the Depth They Need

Different blinds need different minimum depths for an inside mount. Roller blinds are often slim, while Roman blinds, honeycomb blinds, venetian styles and wooden slats may need more space for the headrail and stacked fabric. Check the product details for the minimum depth, and compare it with your measurement before choosing a type.

If your recess is shallow, some makers offer low-profile headrails or shallow-recess fixings. Others suggest an outside mount instead, where the blind sits on the wall or frame above the window. An outside mount can also suit windows with deep sills, handles that protrude or uneven recesses. Weigh the look: inside mounts are neat and show off the frame, while outside mounts cover a larger area and can improve light blocking.

Consider how the blind will operate. Cord, chain, cordless and motorized styles need different clearances. If there are children or pets in the home, look at safety features and child-safe cord guidance from the maker, and follow local rules. Think about light gaps at the sides too, since inside-mount blinds are made slightly smaller than the recess and will let a little light past the edges. Check the product details if privacy or blackout performance matters to you.

Handling Handles, Cranks and Awkward Windows

Window hardware is the most common cause of fit problems. A handle that protrudes into the recess can prevent a blind from hanging straight or from being lowered fully. Crank handles on casement windows, for example, may collide with the blind when it is closed. Measure how far each item sticks out and compare that with the blind’s depth and the space it needs.

For tilt-and-turn windows, check that the window can still open as intended once the blind is fitted. For sash windows, consider whether the blind will sit on the upper or lower sash and whether it will interfere with the lock. Bay windows need each section measured separately, and corner posts or angles can affect the fit. Tall windows may need a second set of hands and a ladder. A short sketch with arrows showing where each handle sits helps if you later need to talk to the seller, because it replaces a long description and prevents mistakes about which side the obstruction is on.

  • Record the position and projection of every handle or lock.
  • Take a photo of each window with a tape measure in view for reference.
  • Note whether trim or beading can be removed or whether the blind must work around it.
  • Ask the seller whether an extension bracket or spacer can help clear a protruding part.

Ordering and Fitting Checks

Before you place an order, read the seller’s measuring and ordering instructions again with your sheet beside you. Confirm whether they want the exact recess size or a figure with an allowance taken off, the unit they expect, and whether width is entered before height. A transposed number is a common ordering error.

Check each window against your notes, and review the order summary before paying. If you are ordering several blinds, consider ordering one first to test the fit, especially if your windows vary. Keep the receipt and the returns policy, since made-to-measure blinds are often non-returnable, so accuracy matters.

When the blinds arrive, compare their size with your records before drilling. Hold the blind in the recess to check that it fits freely and that it clears hardware. Use the supplied fixings suited to your wall and recess material, and follow the maker’s fitting guide. Check that the blind operates smoothly and stops where it should. If a blind is too tight or too loose, contact the seller promptly, quoting your measurements. Keep your measurement sheet in a safe place for later use, such as when you replace a blind or add a new window. If anything about a window is unusual, such as an arched top or a very wide opening, mention it to the seller before ordering, since some blind types are made in limited sizes or need extra supports.

Common Questions

Do I measure the glass or the recess?

For inside-mount blinds, measure the recess, which is the opening the blind will sit in. The glass size is not the right number. Follow the seller's instructions about which edge to measure.

Should I measure in the morning or evening?

Time of day does not matter for accuracy. Measure when you have good light and a clear view. Temperature and humidity can cause slight changes in some materials, but not enough to matter in most homes.

How much gap should there be at the sides?

Makers build in a small clearance so the blind moves freely. The amount differs by seller and type, so follow their guidance and do not add your own allowance.

Can I use inside mount if my window opens inward?

Often yes, if the blind clears the sash and handle. Check the depth and the movement of the window before ordering, and consider an outside mount if space is limited.

What if the recess is uneven at the top?

Check that a headrail can sit securely. If the top is bowed or crumbling, you may need packing shims or a different mount. Ask the seller for advice.

Do I need to measure again before fitting?

A quick check against the delivered blind is wise. If anything has changed, such as new trim or paint, measure again before drilling.

Are blinds safe around young children?

Cords can be a hazard. Choose cordless or child-safe designs where possible, and follow the maker's safety instructions and local guidance.

6 Best Faux Wood Blinds: Cordless 2-Inch Slat Picks (2026)

Reference and further practice

IKEA window measurement and curtain planning


STANLEY PowerLock Tape Measure — how to measure a window for inside-mount blinds

Ready to Buy? Start Here

If this guide helped you decide what to look for, these products are a place to start.

STANLEY PowerLock Tape Measure
STANLEY PowerLock Tape Measure

View Stanley PowerLock Tape Measure on Amazon

As an Amazon Associate we earn from qualifying purchases. Prices and availability are shown on Amazon.

Going Deeper: What The smallest true width and the usable depth inside the window recess Really Tells You

Most guides stop at the headline measurement, but the smallest true width and the usable depth inside the window recess is really a bundle of smaller judgements working together. There is the figure itself, the reference points you took it between, the condition of the space on the day you measured, and the way the item will actually be used once it is in place. Treating those as separate things, and checking each one deliberately, is what separates a purchase that settles in quietly from one that needs adjusting, returning or working around for years.

Start by asking what the measurement is protecting you from. In the case of measuring for inside-mount blinds, the honest answer is rarely the object itself; it is the routine around the object. Doors still need to swing, people still need to pass, light and air still need to move, and cleaning still needs to happen underneath, behind and between things. When you measure with those routines in mind, the number you write down represents the space as it is lived in, not the space as it appears in an empty room on the day you happen to measure it.

It also helps to separate the figures you cannot change from the ones you can. Walls, doorways, fixed fittings and the footprint of furniture you are keeping are facts. The position of the new item, the direction it faces, and how much clearance you leave around it are choices. A good plan for blinds respects the facts completely and spends the choices wisely, instead of hoping a tight fact will somehow become flexible once the delivery arrives.

Finally, remember that measurements age. Rooms get repainted, floors get covered, furniture moves and households change. The figures you record today are a snapshot, and the most useful habit you can build is to re-check the critical one, the smallest true width and the usable depth inside the window recess, whenever the room changes in a way that touches it. That single re-check, which takes minutes, protects every decision that was based on the original set of numbers.

A Careful Second Pass: Checking Measuring for inside-mount blinds Step by Step

The first pass through this guide gives you a working set of figures. This second pass is about turning those figures into ones you would trust with an order you cannot easily undo. Work through it in order, with the item or the space in front of you, and do not skip a step because an earlier one went well; each step below catches a different kind of error, and the errors that cause returns are usually the ones nobody thought to look for.

Measure the width in three places

Take the inside width of the recess at the top, middle and bottom, between the actual surfaces the blind must clear. Recesses are rarely parallel, and an inside-mount blind is ordered to the smallest of the three figures, because it has to pass the narrowest point every time it moves. Write the figure down as soon as you take it rather than trusting your memory, and note which point it came from, because the later steps build on these early numbers and a swapped figure is hard to spot once you are comparing listings.

Measure the drop in two places

Measure from the top inside of the recess to the sill at the left and the right. A sill that is not level changes the finished look of the blind’s bottom bar, and knowing the difference in advance lets you decide whether to fit to the shorter or longer side. If the number surprises you, take it once more before moving on. A second reading that agrees gives you confidence, while a different reading tells you the tape slipped, the surface was not square, or something in the way distorted the first attempt.

Check the depth honestly

Measure how deep the recess is and compare it with the space the blind’s headrail and slats or fabric need, including the operating position. A blind that fits the width but projects from a shallow recess catches on handles and looks unfinished, so depth is a fitting figure, not an afterthought. Keep the tape or ruler in the same orientation for every reading in this step. Changing how you hold it halfway through a set of measurements introduces small differences that add up and can make two matching items look as though they do not match.

Find every obstruction

Look for window handles, vents, tiles, alarm sensors and trim that project into the recess, and note where each one sits. The blind must clear or work around all of them, and the position of an obstruction often decides where the headrail can be fixed. Note any obstruction, slope or soft surface that affected this reading next to the number itself. When you come back to your notes days later, that short comment explains why one figure differs from the others and stops you discarding the wrong one.

Check the recess is square enough

Compare diagonal measurements or use a large square against the corners to see how far the recess leans. A blind is made square, so a recess that is visibly out of square will show uneven gaps; knowing the amount lets you judge whether inside mounting is still the right choice. Compare this figure with the one from the previous step before you continue. The two should tell a consistent story about the space; if they contradict each other, it is far easier to re-check now, while everything is still in place, than after an order arrives.

Record figures before any deductions

Write down the exact recess measurements as taken, and keep them separate from any ordering figures. Deductions for clearance are usually made by the maker from your exact figures, and mixing the two sets is how blinds arrive a size smaller than the window needed. Take a quick photograph of the tape in position if you can. A picture settles arguments with your own notes later, shows a partner or housemate exactly what you measured, and gives you a reference if you need to ask a seller a question.

When you finish, read the full set of figures aloud once, in order. Hearing them as a list makes inconsistencies obvious in a way that scanning a page does not, and it gives you a natural moment to ask whether the numbers describe the space you are standing in. If anything sounds wrong, it probably is, and now is the cheapest possible time to find out.

How Measuring for inside-mount blinds Plays Out in Everyday Situations

Measurements become real when they meet a routine. The situations below are the ones readers describe most often when a choice about blinds either proves itself or starts to annoy, and each one tests the smallest true width and the usable depth inside the window recess in a slightly different way. Read them against your own household and note which of them resembles your busiest, least tidy day, because that is the version of life your decision has to survive.

A bathroom window with tiles part-way up

Tiled splash zones often run into the recess and reduce its width at exactly the height where the blind hangs. Measuring above and below the tile line, and ordering to the tighter figure, prevents the common discovery that a blind fits the top of the recess and jams where the tiles begin. The lesson from situations like this is that the smallest true width and the usable depth inside the window recess only makes sense in context. A figure that looks generous on paper can feel tight once real life fills the space around it, and a figure that looks modest can work well when the layout supports it. Work through your own version of this scenario with your actual numbers before you commit, and pay attention to the moments of the day when the space is busiest, because that is when a poor fit stops being a minor irritation and starts changing how you use the room.

A kitchen window over the sink

Over a sink, the blind competes with taps, washing-up and steam. An inside mount keeps the blind clear of the worktop activity, but the drop must be judged against splashes and the sill’s clutter, and the recess depth must clear the window handle you use every day, not just the closed window. What helps most here is rehearsing the routine rather than imagining the object on its own. Walk through the movements involved, in the order you would really make them, and notice where you turn, pause, set things down or reach past something else. If a rehearsal feels awkward with nothing in place, it will feel worse once the real item arrives, so treat that awkwardness as useful information and adjust the plan, the position or the size while changing your mind is still free.

A deep-set window in an old house

Thick walls give generous recesses that suit inside mounting beautifully, but old recesses are the least likely to be square or parallel. The three-width routine earns its keep here, and the charm of the deep reveal survives as long as the blind is ordered to the recess as it is, not as it should be. Households differ, and this is where a choice that suits one home quietly fails in another. Think about who else uses the space, how often, and what they bring with them, from bags and coats to toys, laptops and laundry. A decision about measuring for inside-mount blinds that accounts for the busiest realistic day, rather than the tidiest possible day, tends to keep working long after the novelty has worn off and the space has settled into everyday use.

Care, Cleaning and Storage That Protect the Fit

A good fit is not permanent by default. Dust, moisture, heat, sunlight and ordinary wear all change how blinds sit, hang, slide or stand over time, and many problems that look like buying mistakes are actually care problems that developed slowly. The habits below protect the result you measured for, and they are deliberately simple, because a routine you keep beats an elaborate one you abandon by the second month.

Dust slats and fabric little and often

Blinds collect dust on every horizontal surface, and a light weekly pass with a soft brush or cloth is far easier than rescuing a blind that has gone grey. Work from the top down so dislodged dust falls onto surfaces you have not cleaned yet, and support fabric blinds rather than pulling them. Build this into a routine tied to something you already do, such as a seasonal clean or the start of a new term, rather than relying on noticing a problem. Small, regular attention of this kind protects the fit you worked to achieve and catches wear while it is still cheap and simple to deal with.

Keep moisture away from mechanisms

In kitchens and bathrooms, wipe condensation from the recess and the headrail rather than letting it sit, because the moving parts and cords suffer before the slats do. A blind that is raised and lowered regularly also dries more evenly than one left closed against a damp window. Always check the care label or the maker’s instructions for the specific item before using any product or method on it, because materials that look similar can react very differently. Test anything new on a hidden area first, and stop if the surface changes colour, texture or smell.

Operate the blind evenly

Pull cords and wands straight and gently, and raise the blind evenly rather than letting one side race ahead. Uneven operation twists slats, strains ladders and cords, and is the usual reason a blind that fitted perfectly begins to hang crooked in its recess. When you store or move the item, protect the edges, corners and surfaces that decide how it sits and fits. Damage usually happens in cupboards, lofts and hallways rather than in daily use, and a few minutes of padding or careful stacking prevents the slow distortion that later shows up as a poor fit.

Once or twice a year, do a short fit audit: stand back, look at how the item sits compared with the day it arrived, and re-check the smallest true width and the usable depth inside the window recess if anything has shifted, sagged, swollen or shrunk. Catching a small change early usually means a small correction; leaving it means the same correction later, plus whatever the poor fit has been doing to the floor, the wall or the item itself in the meantime.

Comparing the Options in This Guide Against Each Other

Once your shortlist is down to the options discussed in this guide, the temptation is to choose by appearance and be done. Resist it for ten more minutes and compare those options on the points that decide daily satisfaction with blinds. The criteria below are the ones that most often separate the pick that keeps pleasing from the pick that merely looked right on the screen, and each one can be checked from the details already given in this guide and in the listings themselves.

Headrail depth against your recess

Compare each option’s headrail and operating depth with your shallowest recess measurement, not the deepest. The option that sits comfortably within the recess, with room for the window handle, is the one that will look built-in rather than squeezed in. Put the figures for this point side by side for every option on your shortlist, using the same units and the same reference points. Listings describe things in different ways, so the honest comparison is the one you build yourself from your own worksheet rather than the one assembled from marketing headings.

Slat or fabric behaviour in the space

Wide slats, fine slats and fabric vanes each need different room to tilt and stack within the recess. Compare how much of your recess depth each option uses when open, because a blind that fills the recess when raised steals the light the inside mount was meant to preserve. Treat this as a pass-or-fail check rather than a matter of taste. An option that fails here will not be rescued by a colour you love or a finish that matches the room, because you will meet this limitation every single day, long after you have stopped noticing how the item looks.

Control position and handedness

Options differ in which side the controls fall and how they hang against the recess wall. Compare that detail against your obstructions list: a control that lands behind a projecting handle or a tiled corner will annoy you every day, whichever fabric or slat you choose. If two options look equal on this point, let it go and move to the next criterion instead of forcing a difference that is not really there. Shortlists are decided by the two or three points where options genuinely differ, and those are the points worth your time and questions.

Write your comparison down as a simple grid, one row per option and one column per criterion, and mark only clear wins rather than inventing scores. The right choice usually identifies itself in that grid: it is the option with no failures on the points you cannot compromise, even if another option beats it on a point you care about less.

Mistakes That Only Show Up After a Few Weeks

The mistakes that matter most with measuring for inside-mount blinds rarely appear on the first day. On the first day everything is new, the room is tidy, and you are paying attention. The problems arrive later, disguised as small daily frictions: the thing that has to be moved before something else can be used, the corner that never gets cleaned because access is awkward, the item that is always slightly in the way of a door, a drawer or a person. Each friction is trivial alone; together they are how a reasonable purchase turns into a quiet regret.

One common pattern is measuring for the object but not for its life. Blinds get opened, pulled out, sat on, walked around, cleaned under and bumped into, and each of those actions needs room that a footprint measurement does not show. When you review your figures, add a mental rehearsal of the object’s busiest hour and ask where everyone and everything stands during it. If the rehearsal needs someone to hold something, move something or wait for something, the plan, not the household, should change.

Another pattern is trusting a single measurement taken once, in a hurry, in an empty room. Floors slope, walls wander, cushions compress and fabrics relax, and a figure that was accurate for the object alone can still be wrong for the object in use. The defence is boring but effective: measure twice, at the points of greatest stress, and keep the least forgiving figure as the one you plan around. Planning around the tightest honest number feels cautious; living with the result feels easy, which is the point.

The last pattern is forgetting that other people use the space differently. The person who measured imagines their own routine and, without meaning to, plans for a household of one. Children, partners, guests, pets and future occupants all bring their own heights, habits and belongings. A decision about measuring for inside-mount blinds that has been tested against at least one other person’s routine, ideally the person least like you, survives contact with real life far better than one tested only against your own.

More Questions Readers Ask

The common questions earlier in this guide cover the essentials. The questions below come up once people have measured, ordered or lived with the result for a while, and they are answered here in the same spirit: from your own figures first, and from general product claims last.

Should I deduct anything from my measurements myself?

For most inside-mount orders, no: you supply the exact recess figures and the maker deducts a small clearance allowance so the blind moves freely. The product’s ordering instructions are the authority here, so read them before ordering and follow their convention exactly rather than combining two systems of deductions.

What if my three width measurements are all different?

That is normal, and it is exactly why you took three. Order to the smallest width so the blind clears the tightest point, and expect the small gaps at the wider points to be barely visible once the blind is fitted, especially if the recess is painted a similar tone to the blind.

My recess is too shallow. What are my options?

A shallow recess usually means choosing a slimmer blind style, accepting that part of the headrail projects, or switching to an outside mount on the wall or frame. None of these is a failure; the mistake is ordering a deep blind for a shallow recess and discovering the projection after the holes are drilled. A quick rehearsal with tape, boxes or a paper template usually settles questions like this in minutes and is far more reliable than picturing the result and hoping for the best.

Do I measure to the sill or past it?

For an inside mount, the drop normally ends at the sill, because the recess ends there too. Measure to the sill surface the bottom bar will rest just above, and note anything that lives on the sill permanently, since the blind must finish behind or above it rather than through it. Keep your written measurements with the order confirmation or guarantee paperwork, so that if the question comes up again you can answer it from your notes instead of starting the whole process again.

Can I fit an inside-mount blind if the window opens inwards?

Only if the recess depth lets the blind and the opening window coexist, which is uncommon. Check the sweep of the opening casement against the blind’s fitted position before ordering; where they collide, an outside mount or a blind fitted to the window itself is usually the workable answer. If two people in the household disagree, let the measurements arbitrate: test both ideas against the figures you recorded, and choose the one that works on the busiest day, not the quietest.